SPIRENT TEST CENTER USER GUIDE PDF
while the DUT is playing the role of PCE Besides, Spirent TestCenter allows the user to configure or adjust the attributes, e g cost and bandwidth, of. Spirent TestCenter™ minimizes that risk by mirroring actual network scenarios and traffic Ŋ Automatically configure traffic with dynamic IP and. mAc addresses. 19 Nov User Documentation Spirent TestCenter user documentation is available in PDF format and as online Help files:? Documents delivered in PDF.
|Published (Last):||8 March 2006|
|PDF File Size:||7.38 Mb|
|ePub File Size:||4.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
This also creates problems when doing multistream at layer 2 since the source macs will be modified.
For RFC tests, tesh the locations for the monitoring ports is mandatory. If the final verification does not pass the test with the lossrate specified it will continue spirent test center user guide binary search from its previous point. This example will use Spirent TestCenter v4.
True, supported only by IxNet ‘l2’: For certain tests it may be beneficial to usre some packets before starting test traffic to allow switch learning to tsst test center user guide place. In case of a Dummy traffic generator it is possible to pre-configure the test results. Select a version of Spirent TestCenter software to utilize. Dictionary with dummy results can be cdnter by CLI argument —test-params or specified in Parameters section of testcase definition.
For best practice results in deploying STCv, the following is suggested:.
How to Using Routing in Spirent TestCenter – OSPF Example
This can be adjusted with the following configurations:. In case of Burst traffic type, the latency statistics are measured guidde all frames in the burst. Contact Xena Networks for the latest version of this tdst. It is assumed the user has access to the Xena If you are using two separate cards then it will take the lowest of the two cards as the max speed.
These parameters centeer to all the tests, yest are mandatory for all tests. Hit Ok and start the TCL server application. To install this package follow the instructions below. Spirrent can perform spirent test center user guide verification run for a longer duration once the binary search of the RFC trials have completed. Such testcase can be run by any user and it will still generate all reports and result files.
Dummy result pre-configuration 3. When your traffic generator has completed traffic transmission and provided the results please input these at the VSPERF prompt. Such testcase can be run by any user and it will still generate all reports and result files.
Please check the list of traffic-type-metrics. It is recommended to verify, that any new file inserted into c: In case of burst traffic type, it enables latency measurements for all frames. For installation, select the version that matches the Spirent TestCenter Application version. Continuous Traffic Testing 3.
To remove this limitation enable promiscuous mode on T-Rex guidf allow all packets regardless of the destination mac to be accepted. The list of metrics can be found at traffic-type-metrics. You can also modify the traffic transmission duration and the number of tests run by the traffic generator by extending the example commandline above to:.
RFC Sporent and Continuous: Please send ‘continuous’ traffic with the following stream config: This allows simple function calls, nearly identical to those provided by StcPython. After the transmission is completed you could specify values for all collected metrics and VSPERF will use them to generate final spirent test center user guide. This feature can be enabled in the configuration files as well as the length of the final verification in seconds. Card Bandwidth Options 3.
SPIRENT TEST CENTER USER GUIDE PDF DOWNLOAD
This spirennt can be enabled in the configuration files as well as the length of the final verification in seconds. The stcrestclient package provides the stchttp. The following parameters must be set to allow for proper connections to the host with MoonGen. On the CentOS 7 System 3. T-Rex can perform a verification run for a longer duration once the binary search of the RFC trials have completed. The below configurations can be adjusted to enable this. Test results share 3.
The default options for the following are optimized for best results. Or example of configuration file can be found at location below, but it must be updated manually:. The following parameters must be set to allow for proper connections to the host with Trex. This will setup the vSwitch and the VNF if one is part of your test print the traffic configuration and prompt you to transmit traffic when the setup is complete.
This can be configured with the following params. The user can also visit www. Metrics collected for supported traffic types 3.
ESXi Virtual test port performance is affected by the hypervisor configuration. Create a new directory at DUT, where shared directory with results will be mounted, e. If the final verification does not pass the test with the lossrate specified it will continue the binary search from its previous point.