PT2272 PDF

The PTM4 (Rx) receiver module is designed to be used in conjunction with the PT (Tx) transmitter module (Item HCMODU). When used together. PT PT is a Remote Control Decoder Paired With PT Utilizing CMOS Technology.. is a remote control decoder paired with PT utilizing. PTL4 PT is a Remote Control Decoder Paired With PT Utilizing CMOS Technology.. is a remote control decoder paired with PT utilizing.

Author: Shakak Faesida
Country: Tajikistan
Language: English (Spanish)
Genre: Medical
Published (Last): 22 January 2012
Pages: 380
PDF File Size: 18.81 Mb
ePub File Size: 5.22 Mb
ISBN: 612-9-70523-218-4
Downloads: 33849
Price: Free* [*Free Regsitration Required]
Uploader: Faenris

RF Decoder – PT – Mhz [] : Sunrom Electronics/Technologies

February 25, at Basically the same steps for operating 4 lamps. June 29, at 3: Now depending upon the type of application, the RF module is chosen. After soldering the circuit, connect the fluorescent lamps and the plug top to the 3 pins terminal block as shown as the below.

So before we use them, we have to set their adresses the same. Add a simple wireless control to a device, no addressing, no programming — used a MHz remote with this receiver and you have wireless control up to meters away under ideal conditions!

December 31, at The video on how the Ph2272 modules functioning was shared at the end of this tutorial. More posts by cl. April 24, at RF Modules are used wireless transfer data and low cost application. PTM4 data received flow char Click to Enlarge. WirelessRemote Control. November 29, at March 11, at 1: April 23, at 3: June 14, at 6: It encodes data and address pins into a serial coded waveform suitable for or IR modulation. September 3, at 6: The Led and the relay will be switch off.

TOP Related  REINVENTA TU VIDA JEFFREY YOUNG PDF

And the “H” means they are connceted with positive power supply. Hi all, Please continue discuss in technical forum. April 15, at 7: Py2272 11, at November 12, at 6: As shown above, jumper pad area is composed of three rows.

HTML is not translated! Now the output was becoming 0. Can somebody advise me to resolve this?

If you solder the address pin with the “L”, it means you set the pin to low. I was intend to use this to send wireless level indicator signal from my water tank.

PT2272-L4S SOIC-20 – RF Decoder – Latch Output

This makes them suitable for remote control applications, as in where you need to control some machines or robots without getting in touch with them may be due to various reasons like safety, etc. Package Included 1 x Transmitter with battery 1 x Receiver.

February 21, at 7: April 3, at 2: The corresponding Led will light up and switch on the relay.

TOP Related  PYTHON FOR EVERYONE CAY HORSTMANN EBOOK

January 18, at 1: February 26, at 4: August 26, at On the right of the top row ;t2272 marked an “L”, where means this row is connected to GND. The only different is the RF frequency. December 5, at 3: Only while the transmitter PT and receiver PT have the same address, they can communicate. So it has valid address.

The tutorial is end here. Highly appreciated your reply, thank you.

It should works for MHz. Would it work with MHZ? It has 12 bits of tri-state address pins providing a maximum ofor address codes; thereby, drastically reducing any code collision and unauthorized code scanning possibilities. There are three states: PT has a maximum of 12 bits of tri-state address pins providing toor address codes; thereby, drastically reducing any code collision and unauthorized code scanning possibilities.

I would try to modify a wireless bell, to make an garage opener, and of course a controller for light in house. Add to Wish List. If you solder it with “H”, it means high.