JIS K 6301 STANDARD PDF DOWNLOAD
Find the most up-to-date version of JSA – JIS K at Engineering COM PDF – Search results, DOWNLOAD. JIS K STANDARD SDOCUMENTS2. COM jis k standard pdf Specimen. Sample Cutting Dies Ã ¢â‚¬â€œ. cert. no. ) 03/20/ page 1 of 14 scope of accreditation to iso , Jis K Free Download Here JIS K. physical testing methods .
|Published (Last):||4 February 2008|
|PDF File Size:||16.44 Mb|
|ePub File Size:||4.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
JSA – JIS K – Physical Testing Methods for Vulcanized Rubber; Errata – 5/ | Engineering
Then, long leg type complies with DIN Our product line consists of various types of durometers applicable to specific materials as indicated jis k 6301 standard the chart above. Jis k 6301 standard Pressure foot jsi contact with the specimen is 44mm in width and 18mm j depth, wide enough to ensure accurate measurement. However, it is sandard even now for measurement data or internal management data upon the agreement of concerned parties due to its extensive use historically within the rubber industry.
The most important consideration in using durometers is to select the correct type for purposes of measurement according to the specimen.
Pressure foot The Pressure foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough to ensure accurate measurement. At that time, deep hole H and long leg type L make measurement possible by making pressed face small or long. To top of product information.
GS 4kg weight option ZY The stationary set hand max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen. It consists of 3 types of durometer such as Type A jis k 6301 standard medium stiffness, Type D for high hardness and Type D for low hardness.
Hardness Tester Selection Chart Our product line consists of various types of durometers applicable to specific materials as indicated in the chart above.
Constant Loader for Durometer Constant loarder assures uniform test pressure eliminating false readings jos to differences between operators in measuring by hand. JIS K which had been established in and sustaining the base of rubber industry jis k 6301 standard Japan was discontinued in after the suspended period, as it was not in conformity with ISO, and JIS K was newly established.
Please select according to usage in addition to type A and Type D. Type D is suitable for hard rubber of jis k 6301 standard measured figure by Type A 90 and above and Type E is suitable for soft rubber of which measured figure is below Measurement example Hardness is being measured by placing GS G on the sponge sheet.
Product Testing & Calibration – Rubber & Rubber Products: Material/Product Testing
However, it was used for 3601 years as rubber hardness measurement and is still used as test data agreed shandard concerned persons even now when it is progressed to shift to new JIS and the standard is discontinued. This is basically equal to JIS K of durometeras only its round up method of spring load jis k 6301 standard etc. Two-pointer type max-hand jis k 6301 standard active hand of Rubber Hardness Tester The stationary set hand max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen.
Type A which is main type tends to indicate higher figure by 1 or 2 points compared with conventional A hardness measurement.
However, verification is recommended because a significant difference is estimated to be the largest when a durometer indicates jis k 6301 standard values from 10 to 90 points. Indentor Extension Tester The gauge to check the indentor height on a durometer and the reading indicator mechanism.
Stsndard E 2 durometer with around half of sponge standaed load figure of type E, and type FO to measure hardness of polystyrene sponge for the level of sponge washing dishes are available.
Inspection is conducted at 2, 50, and points respectively. Jis k 6301 standard Tester for Hardness Tester Tester to check load properties of the spring on a durometer Inspection is conducted at 25, 50, and 75 points respectively. Night line and highest and lowest limiter equipped for the both are standard.
There are 2 jis k 6301 standard of A type for general rubber and C type for hard rubber. But we distinguish model code as another durometer from conformity of standard point of view. This standard is ruled by plastic business field in Japan apart from testing method of 6031 of rubber. In case there unevenness on the measured face, less flat face because of irregular shape and deep bump at the bottom, jis k 6301 standard face of durometer is difficult to reach and sometimes accurate measurement is not stajdard.
Dispersion of polystyrene level can be judged. High accuracy and repeatability of the hardness readings are assured by the flexible joint function. As is half ball type osibari this is suitable for soft material like soft rubber expanded rubberhardness of spool of textile and film roll to which osibari sticks if it is jis k 6301 standard Sttandard durometer.