ISO 3382-1 PDF

ISO. First edition. Acoustics — Measurement of room .. ISO , together with ISO and ISO , cancel and replace ISO. NBR ISO Acoustics – Measurement Of Room Acoustic Parameters – Part 1: Performance Spaces. Be notified when this Standard is updated or. In this paper a selection of the most important ISO parameters is at Hz. Room acoustic parameters described in ISO where derived.

Author: Fejin Vosar
Country: Belize
Language: English (Spanish)
Genre: Marketing
Published (Last): 24 July 2017
Pages: 264
PDF File Size: 8.8 Mb
ePub File Size: 20.70 Mb
ISBN: 929-1-11617-560-9
Downloads: 32531
Price: Free* [*Free Regsitration Required]
Uploader: Nitaxe

ISO 3382 2 2008

These measures may be used to give warnings when the decay curve is not linear, and consequently the result should be marked as less reliable and not having a unique reverberation. First, the sound pressure level from noise sources, the intelligibility of speech, and the perception of privacy in a room are strongly dependent on reverberation uso.

If decay values of 5 dB to 35 33821 below the initial level are used, it is labelled T Enviado por Christiele flag Denunciar.

This requires a signal-to-noise level of at least 35 dB. However, a room with up to two persons present may be allowed to represent its unoccupied state, unless otherwise specified.

Reverberation time measurements should be made in a room containing no people. With modern measuring equipment, the decay curves are normally not displayed and this may introduce a risk that abnormal decay curves are used for the determination of the reverberation time. This part of ISO is intended to contribute to the general understanding and acceptance of reverberation time for room quality and usability.

The introduction of the option of a survey measurement is intended to promote more frequent measurement of reverberation time in rooms where it is relevant. There are several reasons to measure reverberation time. For undated references, the latest edition of the referenced document including any amendments applies.

TOP Related  GHANTASALA BHAGAVAD GITA FULL EBOOK

ISO Acoustics – Measurement of Room Acoustic Parameters. Part 1 – Google Books

Second, reverberation time is measured to determine the correction ido for room absorption inherent in many acoustic measurements, such as sound insulation measurements according to ISO all parts and sound power measurements according to ISO An alternative measurement 33882-1, however, is to use a period of maximum-length sequence MLS type signal or other deterministic, flat-spectrum signal like a sine sweep and transform the measured response back to an impulse response.

Annex A contains some additional information about the measurement uncertainty 33382-1 the reverberation time. However, in the vast majority of rooms, it is left to the design team to specify and design for a reverberation time that is reasonable for the purpose of a room.

The measurement results can be used for correction of other acoustic measurements, e. It is obvious that a very simple measurement is better than no measurement.

It is then labelled accordingly. It describes the measurement procedure, the apparatus needed, the required number of measurement positions, and the method for evaluating the data and presenting the test report.

For dated references, only the edition cited applies.

The main difference concerns the number of measurement positions and thus the time required for the measurements. The traditional measuring technique is based on visual inspection of every single decay curve.

In some countries, building codes specify the required reverberation times in classrooms and other categories of room.

SRPS EN ISO 3382-1:2013

Performance rooms ISOAcoustics — Application of new measurement methods 3382- building and room acoustics IECElectroacoustics — Octave-band and fractional-octave-band filters 3 Terms and definitions For the purposes of this document, the following terms and definitions apply.

TOP Related  GLD PROSPECTUS PDF

Reverberation time in ordinary rooms 1 Scope This part of ISO specifies methods for the measurement of reverberation time in ordinary rooms. However, a preference has been given to the 20 dB evaluation range for several reasons: For this reason, Annex B introduces two new measures that quantify the degree of non-linearity and the degree of curvature of the decay curve.

ISO specifies three levels of measurement accuracy: The use of rotating microphones during the measurement of decay curves has been considered by the working group, and this procedure is found to be without a clear physical meaning and thus it is only accepted for the interrupted noise method and only when the result is used for a correction term.

This part of ISO does not repeat the technical details of ISObut deals with the measurement of reverberation time, only, in any kind of room.

Thus, this part of ISO fills a gap among measurement standards for acoustic properties of buildings. Uso of ISO Thus, if T is derived from the time at which the decay curve first 3382-1 5 dB and 25 dB below the initial level, it is labelled T If the measurement result is used for correction of a. Rooms may include domestic rooms, stairways, workshops, industrial plants, classrooms, offices, restaurants, exhibition centres, sports halls, and railway and airport terminals.