BENDIX KING KY97A PDF
This manual contains information relative to the physical, mechanical, and electrical characteristics of the Bendix/ King KY 96A and KY 97A VHF Communication. Find great deals for Aircraft Transceiver Bendix King KY 97a TSO. Shop with confidence on eBay!. MM dwd. RH REVISION HISTORY. MAINTENANCE MANUAL. BENDIX/KING. KY 96A, KY 97A. VHF Communication Transceiver.
|Published (Last):||21 October 2005|
|PDF File Size:||5.78 Mb|
|ePub File Size:||12.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
Bendix/King KY97A VHF AM Comm
A flashing display will alert the pilot to a microphone that becomes stuck for two minutes. This is to permit the t ransmitter tube t o warm-up and stabil ize. Shown by arrows Slide connector cap, with benxix hole in positi on to c l ear dielectric, on to connector unti. The KY96A and KY97A offer operators a consistent audio level-automatically amplifying weak audio signals and muting those which are too strong.
Contact Insertion into Molex Connector Housing 1.
C, C, C, C, C Bendix King KY97a Squelch. Sign up for price alert. You have no items ling your shopping cart. Simply tune the desired frequency into the standby window “STBY” while monitoring the “USE” channel-when the time is right, simply push the frequency transfer button to transfer the standby frequency into the active window.
Looking down, the blade can be seen sliding into the stop. Secure the mounting tray KPN – to instrument panel oer Figure 2 Please, log in or kinh.
Bendix/King – KY97A – Communications Transceiver (14V)
All quality goods supplied by Mendelssohn Pilot Supplies are fully guaranteed and all items will be shown clearly in your shopping basket. Thread Tools Show Printable Version. Hi, Guys I have a Bendix KY97a in by Bell, the squelch threshold is set way, way to high, have to pull out the squelch knob when we need to copy even half strength stations, does anybody know if it is possible to adjust this? Our price is lower than the manufacturer’s “minimum advertised price. A one-shots at TP and TP for 8.
Bendix/King KY97A VHF AM Comm
Contact 03 Fax: With the ease and speed of a push button you can switch klng active and standby frequencies. The surface bendox beneath the antenna should be a nat plane over as large an area as possible. Internally set with jumpers behind face plate. A remote switch may be installed as an additional means of providing the “flip-flop” function. In addition the KY 97A transceiver displays transmit and receive annunciations, to verify your active COMM and alert you if any audio settings may be incorrect.
The KY 97A also incorporates an audio amplifier with three audio inputs, eliminating the need for a seperate audio panel in some ky97q. The series resistor is not required in 14V installations. A low cost COMM has a different appeal to different pilots. Repeat Step 3 for the insulator tabs.
Kiny flashes within this interval may be f rom noise, a second or t h ird int errogat or, or from side lobes from interrogat ors with out side lobe suppression.
If necessary, straighten the contact terminal while it is held by the crimper. Solder cont act to center conductor. Providing VHF communications in the The KY 97A also incorporates an audio amplifier with three audio inputs, eliminating the need for a seperate audio panel bendux some cases.
There are adjustments but would normally be carried out on the bench!
Bendix-King KYA (14v) | Mendelssohn Pilot Supplies
An additional feature of the transponder and beacon system is the S. Consult the manufacturers current data. After being turned on there is a 30 second delay before t he unit b ecomes functional.
The antenna should be well removed from any projections, the engine s and propeller s. Other pilot useful capabilities include automatic radio levelling, to boost weak signals and mute excessively strong ones, and automatic squelch override. Find More Posts by avionicsmoke. The antenna should be kept clean.
When the ejector is slid into place, the locking key of the contact is raised allowing the contact to be removed by pulling moderately on the lead. Our website requires cookies to provide all of its features. However, it is recommended that the separation between DME and transponder antennas be at least six feet.